Model No. WEBE11880
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USERÕS MANUAL
PATENT PENDING
Important Precautions
To reduce the risk of serious injury, read the following important
precautions before using the weight bench.
WARNING:
1. Read all instructions in this manual before
using the weight bench.
12. The weight bench is designed to support a
maximum of 360 pounds, including the user,
a weight bar, and weights. Do not place more
than 110 pounds, including a barbell and
weights, on the weight rests; do not place
more than 50 pounds on the leg lever for
normal use.
2. Use the weight bench only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
13. When using the backrest in an inclined posi-
tion, make sure that the support rod is fully
inserted into the uprights and that the lock-
ing hook is in place.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench for
protection.
14. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
5. Inspect and tighten all parts each time you
use the weight bench. Replace any worn
parts immediately.
15. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental or institutional setting.
6. Keep children under the age of 12 and pets
away from the weight bench at all times.
7. Always use an equal amount of weight on
each side of the barbell (not included).
16. When you are using the lat bar, always stand
clear of the lat upright since the weight car-
riage will swing around the upright as it is
raised.
8. Do not use a barbell (not included) that is
longer than five feet with the weight bench.
17. Always disconnect the lat bar from the
weight bench when you are performing an
exercise that does not use the lat bar.
9. When you are using the leg lever, place a
barbell (not included) with the same amount
of weight on the weight rests to balance the
bench.
18. Never let go of the lat bar when you have
weights raised. The weight carriage will fall
with great force that may cause injury or
damage the weight bench.
10. Always wear athletic shoes for foot protec-
tion while exercising.
11. Keep hands and feet away from moving parts.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
3
Before You Begin
Thank you for selecting the versatile WEIDER¨ T28
Weight Bench. The WEIDER¨ T28 is designed to help
you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic mus-
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is WEBE11880. The
cle size and strength or a healthier cardiovascular sys- serial number can be found on a decal attached to the
WEIDER¨ T28 Weight Bench (see the front cover of
this manual).
tem, the T28 Weight Bench will help you achieve the
specific results you want.
For your benefit, read this manual carefully before
using the WEIDER¨ T28 Weight Bench. If you have
additional questions, please call our Customer Service
Department toll-free at 1-800-999-3756, Monday
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Cable
Lat Bar
Weight Tube
Weight Rest
Carriage Pin
Weight Carriage
Upright
Backrest
Lat Upright
Seat
Right
Side
Leg Lever
Foam Pads
Weight Tube
Left Side
4
Assembly
Before beginning assembly, carefully read the
following information and instructions:
¥
¥
For help identifying the small parts, use the PART
IDENTIFICATION CHART on page 5.
As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself!
Everything in this manual is designed to ensure
that the assembly of our products can be complet-
ed successfully by anyone. However, it is impor-
tant to recognize that your new equipment is a
sophisticated product with many small parts and
consequently, the assembly process will take
time. Most people find that by setting aside plenty
of time, and by deciding to make the task enjoy-
able, assembly will go smoothly.
The following tools (not included) are required
for assembly:
¥
¥
¥
¥
¥
Two (2) adjustable wrenches
One (1) rubber mallet
One (1) standard screwdriver
One (1) phillips screwdriver
¥
¥
Assembly requires two people.
Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Lubricant, such as grease or petroleum jelly
plus soapy water.
¥
Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches or a set of ratchet wrenches.
1. Before assembling this product, make sure you
have read and understand the information in the
box above.
1
57
Place the Seat Base (50) on the floor next to the
Tower Base (57), as shown in drawing 1.
See drawing 1A. Slide two 5/16Ó x 1 1/2Ó Bolts (56)
through the holes in the indicated bracket on the Seat
Base (50). Slide a 1/2Ó Spacer (54) onto each Bolt.
Slide the Seat Base (50) up next to the Tower Base
(57), and slide the two 5/16Ó x 1 1/2Ó Bolts (56)
through the indicated holes in the Tower Base.
50
1A
15
57
Slide a 5/16Ó Washer (53) onto each of the 5/16Ó x 1
1/2Ó Bolts (56) and secure the Bolts with two 5/16Ó
Nylon Locknuts (15). Do not tighten the Nylon
Locknuts yet.
53
54
53
56
54
56
50
5
2. Identify the Right Base Extension (33) by looking at
the indicated holes. Orient the Base Extension as
shown in the drawing. Note: See the drawing on
page 4 to identify the right and left side of the
bench.
2
49
Attach the Upright (49) and the Right Base Extension
(33) to the indicated bracket on the Tower Base (57)
with two 3/8Ó x 3 1/4Ó Bolts (32) and two 3/8Ó Jamnuts
(11). Do not tighten the Jamnuts yet.
33
32
Holes
11
57
34
3. Lubricate the inside of the Weight Carriage (23). Slide
the Weight Carriage onto the Lat Upright (34) and
lock it in the indicated position with the Carriage Pin
(38).
3
Attach the Lat Upright (34) and the Left Base
Extension (27) to the indicated bracket on the Tower
Base (57) with two 3/8Ó x 3 1/4Ó Bolts (32) and two
3/8Ó Jamnuts (11). Do not tighten the Jamnuts yet.
38
23
11
32
57
27
4. Press a 1 1/2Ó x 1 1/2Ó Outer Cap (58) onto each end
of the Stabilizer (21).
4
58
50
Insert two 5/16Ó x 2Ó Carriage Bolts (22) up trough the
Stabilizer (21). Note: The rubber bumpers on the
Stabilizer must be facing the floor.
21
Place the Stabilizer (21) on the floor next to the Seat
Base (50). Gently lift up the end of the Seat Base and
place the bracket over the 5/16Ó x 2Ó Carriage Bolts
(22) in the Stabilizer.
58
22
6
5. Press a 1 1/2Ó x 1 1/2Ó Inner Cap (7) into the end of
the Bench Frame (5). Place the bracket on the Bench
Frame over the 5/16Ó x 2Ó Carriage Bolts (22) in the
Stabilizer. Hand tighten two 5/16Ó Nylon Locknuts (15)
onto the Bolts. Do not tighten the Nylon Locknuts
yet.
5
7
5
See drawing 5A. Have one person hold up the end of
the Bench Frame (5) while the second person slides
the Bench Rod (8) through the indicated hole in the
Lat Upright (34) until the end of the Rod barely sticks
through the Upright.
15
49
15
21
50
Line up a Bench Spacer (4) with the Bench Rod (8)
and slide the Rod through the Spacer. Slide the
Bench Rod through the pre-assembled Bench Frame
Bushings (6) on the Bench Frame. Slide the Bench
Rod through the second Bench Spacer (4) and then
into the Upright (49).
22
5A
41
51
4
34
6
53
Secure the end of the Bench Rod (8) going into the
Upright (49) with a 1Ó Washer (51), a 5/16Ó Washer
(53) and a Bench Rod Bolt (41).
8
4
Secure the end of the Bench Rod (8) going through
the Lat Upright (34) with a 1Ó Washer (51), a 5/16Ó
Washer (53) and a Bench Rod Bolt (41).
51
41
5
53
Go back and tighten all Locknuts and Jamnuts
6. Attach a Backrest Bracket (2) to the Backrest (1)
with two 1/4Ó x 1/2Ó Screws (3). Make sure the
Backrest Bracket is oriented as shown (note the
position of the indicated hole). Do not tighten
the Screws yet.
6
3
2
3
1
Hole
6a
6a. Refer to drawing 6a. Hold the Backrest (1) in a
vertical position as shown and slide the end of the
attached Backrest Bracket (2) onto the welded rod
on the Bench Frame (5). Hold the other Backrest
Bracket (2) at an angle as shown and slide it onto
the rod.
6b
1
2
2
Refer to drawing 6b. Attach the Backrest Bracket
(2) to the Backrest (1) with two 1/4Ó x 1/2Ó Screws
(3). Note: The Screw nearest the rod should be
attached first.
1
3
Rod
Fully tighten all four 1/4Ó x 1/2Ó Screws (3) used
in steps 6 and 6a.
5
7
7. Attach the Seat (9) to the indicated bracket on the
Bench Frame (5) with two 1/4Ó x 1/2Ó Screws (3).
7
9
Bracket
5
8. Press a 1 1/2Ó x 1 1/2Ó Inner Cap (7) into each end of
the Leg Lever (14).
3
Slide the Weight Tube (17) into the Leg Lever (14)
and secure it with a 5/16Ó x 2Ó Bolt (19) and a 5/16Ó
Nylon Locknut (15). Do not overtighten the Nylon
Locknut.
8
10
Lubricate
14
Press a 1Ó Outer Cap (18) onto the indicated end of
the Weight Tube. Press a 1Ó Inner Cap (16) into the
indicated end of the Weight Tube. Slide a Weight
Stop (55) onto the Weight Tube.
11
18
7
15
5
Lubricate the 3/8Ó x 2 1/4Ó Bolt (10). Attach the Leg
Lever (14) to the bracket on the Bench Frame (5) with
the Bolt and a 3/8Ó Jamnut (11). Do not overtighten
the Nylon Locknut, it must be easy to pivot the
Leg Lever.
55
19
17
16
7
9. Press a 3/4Ó Inner Cap (12) into each end of the two
Pad Tubes (20).
9
13
14
12
Slide the Pad Tubes (20) into the indicated holes in
the Leg Lever (14).
20
Slide a Foam Pad (13) onto each end of both Pad
Tubes (20).
13
13
12
13
10. Locate the Cable (40). Note that one end of the Cable
has a ball and the other a closed loop.
46
10
47
Attach the closed loop on the Cable (40) to the brack-
et on the Weight Carriage (23) with a 3/8Ó x 1Ó Lat
Bolt (26), a 3/8Ó Washer (31) and a 3/8Ó Jamnut (11).
34
42
30
Front View
Bracket
Wrap the Cable (40) around a Pulley (42) in the direc-
tion shown. Attach the Pulley and a Cable Trap (47)
to the bracket on the Lat Upright (34) with a 3/8Ó x 1
1/2Ó Pulley Bolt (46), and a Square Nut (30). Note:
The Square Nut fits into the bracket on the Lat
Upright. It will be easier to hold the Nut with a
pair of needle nose pliers while threading the Bolt
into it. Make sure the Cable Trap is oriented as
shown.
30
40
34
11
47
46
26
31
23
42
8
11. Wrap the Cable (40) around a Pulley (42) in the direc-
tion shown. Attach the Pulley to the Lat Upright (34)
with a 3/8Ó x 4 1/2Ó Pulley Bolt (44), a 3/8Ó Washer
(31), a Pulley Spacer (48) and a 3/8Ó Jamnut (11).
Note: Make sure the Cable is between the Pulley
and the welded pin on the Lat Upright.
11
12
31
Welded Pin
44
34
42
48
40
Press a 3/4Ó Inner Cap (12) into each end of the
Support Rod (25)
25
11
Make sure all parts are properly tightened before
using the weight bench. The use of all remaining
parts will be explained in Adjusting the Weight
Bench beginning below.
12
Adjusting the Weight Bench
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 10 for impor-
tant information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise poster to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
49
The Backrest (1) can be used in a level position or an
Locking
inclined position. To use the Backrest in a level position,
Hook
let the Backrest Brackets (2, not shown) rest on the
25
Bench Spacers (4).
To use the Backrest (1) in an inclined position, lift one
end of the Backrest. Insert the Support Rod (25) into the
1
holes in the Uprights (49, 34). Rotate the Support Rod
until the welded hook locks into place around the Upright
34
(49). Rest the Backrest Brackets (2, not shown) on the
Support Rod.
4
USING THE LAT BAR
To use the Lat Bar (36), first remove the Support Rod (25)
and lower the Backrest (1) to the horizontal position.
Remove the Carriage Pin (38) and lower the Weight
Carriage (23) to the lowest position. Slide the desired
weights (not included) onto the weight tube on the Weight
Carriage. Attach the Lat Bar (36) to the Cable (40) with a
Cable Clip (37).
34
40
37
WARNING: Do not place more than 50 pounds on
the weight carriage. When you are using the lat bar,
always stand clear of the lat upright since the
weight carriage will swing around the upright as it
is raised. Always lower the lat bar slowly, or the
weight carriage will fall with great force.
36
38
Always disconnect the lat bar from the weight
bench when you are performing an exercise that
does not use the lat bar.
23
9
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (14), slide the desired weights (not
included) onto the Weight Tube (17). Make sure the
Weight Stop (55) is mounted on the Weight Tube.
14
55
Weights
WARNING: Do not place more than 50 pounds on
the leg lever for normal use.
17
Exercise Guidelines
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
ness program, and cross training is a very efficient
way to accomplish this. One example of a balanced
program is:
¥ Plan weight training workouts on Monday,
Wednesday and Friday.
¥ Plan 20 to 30 minutes of aerobic exercise, such as
cycling, running or swimming on Tuesday and
Thursday.
¥ Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body plus
develop your heart and lungs.
The only way to increase the size and strength of
your muscles is to push them close to their maximum
capacity. When you progressively increase the inten-
sity of your exercise, your muscles will continually
adapt and grow. You can tailor the individual exercise
to the proper intensity level in two ways:
¥ by changing the amount of weight used
¥ by changing the number of repetitions or sets per-
formed (A ÒrepetitionÓ is one complete cycle of an
exercise, such as one sit-up. A ÒsetÓ is a series of
repetitions).
The proper amount of weight for each exercise obvi-
ously depends upon the individual user. You must
gauge your limits and select the amount of weight that
is right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
PERSONALIZING YOUR EXERCISE PROGRAM
Specifying the exact length of time for each workout,
as well as the number of repetitions or sets for each
exercise, is a highly individual matter. It is very impor-
tant to avoid overdoing it during the first few months
of your exercise program. You should progress at
your own pace and be sensitive to your bodyÕs sig-
nals. If you experience pain or dizziness at any time
while exercising, stop immediately and begin cooling
down. Find out what is wrong before continuing.
Remember that adequate rest and a proper diet are
important factors in any exercise program.
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
WORKING OUT
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group
with emphasis on the areas that you want to develop
Cross Training
Many people desire a complete and well-balanced fit-
10
the most. To give balance and variety to your work-
outs, vary the exercises from session to session.
¥ Rest three minutes after each set for a muscle build-
ing workout
¥ Rest one minute after each set for a toning workout
¥ Rest 30 seconds after each set for a weight loss
workout
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
You will gain the greatest benefits from exercising by
maintaining proper form. This requires moving
through the full range of motion for each exercise and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise poster accompa-
nying this manual, you will find photographs showing
the correct form for several exercises. A description of
each exercise is also provided, along with a list of the
muscles affected. Refer to the muscle chart below to
find the locations of the muscles.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is very effective for increasing flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List
the date, the exercises performed, the weight plus the
numbers of sets and repetitions completed. Record
your weight and key body measurements at the end
of every month.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath!
Remember, the key to achieving the greatest results
is to make exercise a regular and enjoyable part of
your everyday life.
You should rest for a short period of time after each
set. The ideal resting periods are:
MUSCLE CHART
N
O
P
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
A
C. Biceps (front of arm)
B
C
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
Q
R
D
E
S
F
L
T
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
G
M
H
I
U
V
Q. Triceps (back of arm)
J
K
W
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
11
R0699A
Part Identification Chart - Model No. WEBE11880
3/8" x 4 1/2" Pulley Bolt (44)
1/4 x 1/2Ó Screw (3)
3/8" x 3 1/4" Bolt (32)
5/16" Nylon Locknut (15)
Bench Rod Bolt (41)
3/8" x 2 1/4" Bolt (10)
3/8" Jam Nut (11)
3/8" x 1" Lat Bolt (26)
5/16" x 2" Carriage Bolt (22)
5/16" x 1 1/2" Bolt (56)
5/16" x 2" Bolt (19)
Square Nut (30)
3/8" x 1 1/2" Pulley Bolt (46)
1" Washer (51)
5/16" Washer (53)
3/8" Washer (31)
R0699A
Part List - Model No. WEBE11880
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
2
6
2
1
1
3
1
1
1
7
6
4
1
5
2
1
1
1
2
1
2
1
4
1
1
1
7
7
1
Backrest
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
#
2
4
1
1
2
1
1
1
1
1
2
2
1
1
3
1
1
1
1
1
2
2
4
2
1
2
1
2
1
1
3/8Ó Washer
Backrest Bracket
1/4Ó x 1/2Ó Screw
Bench Spacer
Bench Frame
Bench Frame Bushing
1 1/2Ó x 1 1/2Ó Inner Cap
Bench Rod
Seat
3/8Ó x 2 1/4Ó Bolt
3/8Ó Jamnut
3/4Ó Inner Cap
Foam Pad
Leg Lever
5/16Ó Nylon Locknut
1Ó Inner Cap
Weight Tube
3/8Ó x 3 1/4Ó Bolt
Right Base Extension
Lat Upright
Handgrip
Lat Bar
Cable Clip
Carriage Pin
Carriage Pin Knob
Cable
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Bench Rod Bolt
Pulley
Lat Tower Endcap
3/8Ó x 4 1/2Ó Pulley Bolt
Upright Endcap
3/8Ó x 1 1/2Ó Pulley Bolt
Cable Trap
Pulley Spacer
Upright
Seat Base
1Ó Outer Cap
5/16Ó x 2Ó Bolt
Pad Tube
Stabilizer
5/16Ó x 2Ó Carriage Bolt
Weight Carriage
Carriage Sleeve
Support Rod
3/8Ó x 1Ó Lat Bolt
Left Base Extension
Base Bumper
Bumper Screw
Square Nut
1Ó washer
1 1/2Ó x 2Ó Inner Cap
5/16Ó Washer
1/2Ó Spacer
Weight Stop
5/16Ó x 1 1/2Ó Bolt
Tower Base
1 1/2Ó x 1 1/2Ó Outer Cap
UserÕs Manual
Exercise Poster
#
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the userÕs manual for information about ordering replacement parts.
Ordering Replacement Parts
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
1. The MODEL NUMBER of the product (WEBE11880).
2. The NAME of the product (WEIDER¨ T28 Weight Bench).
3. The SERIAL NUMBER of the product (see the front cover of this manual).
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST on page 18 and the
EXPLODED DRAWING on page 19 of this manual).
Limited Warranty
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-
tial damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
Part No. 153351 J00206-C R0699A
Printed in USA © 1999 ICON Health & Fitness, Inc.
|