DOOR OPEN
™
DWV303
POWER
SANIWASH
SANI
ECONO
POWER
ON
OFF
VESTA™ DWV303B
Automatic Compact
Dishwasher
Compact Dishwasher
Contents
Unit Parts Identification
1
2
Installation
Important Safety Instructions
Instructions and
Use & Care Guide
Installation Instructions
Installation Requirements
Built-in Installation
Countertop Installation
Disconnecting Your Dishwasher
3
4
5
6
Use & Care Guide
Loading the Dishwasher
Using the Right Detergent
Using a Rinsing Agent
Pre-Rinse, Sani, Econo Features
Operating Instructions
7
7
7
8
9
9
Program Summary/Selection Chart
Troubleshooting
Common Problems/Solutions Chart
If You Need Service
10
10
Warranty Statement
11
READ ALL INSTRUCTIONS BEFORE USING
UNIT PARTS IDENTIFICATION
3
4
5
6
7
1
2
8
9
11
10
1. WINDOW
18. DISH RACK (NOT SHOWN)
2. FRONT PANEL
19. SILVERWARE
3. DOOR RELEASE BUTTON
4. LED (POWER)
5. LED (SANIWASH)
BASKET (NOT SHOWN)
20. RINSE AGENT MEASURING
CONTAINER (NOT SHOWN)
6. SANIWASH/ECONO BUTTON
7. POWER (ON/OFF) BUTTON
8. PROGRAM/TIMER SELECTOR
9. WATER INLET CONNECTION
10. DRAIN HOSE CONNECTION
12
13
11. POWER CORD - 6’ Length (182.8 cm)
12. RINSE AGENT DISPENSER
13. SPRAY ARM
14
14. FILTER
15. DOOR ASSEMBLY
15
16. DOOR LATCH MECHANISM
17. DETERGENT (INDENT) LOCATION
16
17
BUILT-IN HOSE KIT (Part# DWVBIHK)
OUTLET HOSE
BUILT-IN TRIM KIT
(Part# DWVTKBL)
COUNTERTOP HOSE KIT
(Part# DWVCTHK)
4' Length
QUICK-CONNECT
FAUCET ADAPTER
(121.9 cm)
TRIM KIT
X 6
OUTLET
HOSE
HANGER
Inlet
5' Length
(152.4 cm)
X 2
INLET HOSE
7-1/2' Length
(228.6 cm)
INSTALLATION BLOCK
OUTLET
Outlet
HOSE CLAMP
1
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
- Items with wooden or bone handles, or items joined together
with glue are unsuitable as they cannot resist hot water.
- Do not touch the heating element during or immediately
after use.
When using your dishwasher, follow basic safety
precautions:
- Do not operate your dishwasher unless all enclosure
panels are properly in place.
- Read all instructions before using the
dishwasher.
- Use the dishwasher only for it’s intended use.
- Use only detergents or wetting agents
recommended for use in a dishwasher and
keep them out of reach of children.
- Do not tamper with controls.
- Do not abuse, sit on, or stand on the open door or dish-rack
of the dishwasher. The machine may topple over.
- Protect cables and hoses from high temperatures.
- To reduce the risk of injury, do not allow children to operate
or play on the dishwasher.
When Loading Items To Be Washed:
- Locate sharp items so that they are not likely to damage
the door seal.
- When removing an old dishwasher for service or discarding
it, remove the door to the washing compartment.
- Load sharp knives with the handles up to reduce the risk
of cut-type injuries.
- Under certain conditions, hydrogen gas may be produced
in a hot-water system that has not been used for two
weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the
hot-water system has not been used for such a period,
before using the dishwasher, turn on all hot-water faucets
and let the water flow from each for several minutes. This
will release any accumulated hydrogen gas. As hydrogen
gas is flammable, do not smoke or use an open flame
during this time.
- Do not load plastic items unless they are marked
“Dishwasher Safe” or the equivalent. For plastic
items not marked as such, check the manufacturers
recommendations.
- Do not load glasses over the dish rack pins. Glasses
loaded over dish rack pins are not properly supported and
are likely to get damaged.
SAVE THESE INSTRUCTIONS
Grounding Instructions:
This appliance must be grounded.In the event of malfunction,
or breakdown, grounding will reduce the risk of electric shock
by providing the path of least resistance for electric current.
This appliance is equipped with a cord having an equipment
grounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
Instructions pertaining to a risk of fire, electric
shock, or injury to persons.
Electrical Instructions:
An electrical supply of 120 volts AC only, 60Hz is required.
Make sure that a suitable electrical supply socket is located
close to where the dishwasher is to be placed.
2
INSTALLATION INSTRUCTIONS
INSTALLATION REQUIREMENTS
All Installations
For Best Results
- Remove all packing materials carefully.
Your dishwasher cleans by spraying a mixture of hot clean
water and detergent (under pressure) against the soiled
surface of dishes. The water is pumped through a rotating
spray arm, drained through a filter (to remove food and soiled
particles) and pumped back through the spray arm.
- Make sure the electrical power supply is within easy reach
of the machine. The power cord is 6 Feet (182.8 cm) long.
- Supply shut-off valves should be easily accessible.
- If the water pipes you will be connecting to are new or un-
used, run the water until clear to remove any debris that
could clog the water valves before connecting the
machine.
Soiled water is pumped out and replaced with clean water
at the end of each cycle (the number of times depends on
the cycle being used). For best cleaning results, the water
temperature must be at least 130°F (55°C). To prevent
dishwasher damage, the temperature of the incoming water
supply should not exceed 160°F (71°C).
- The dishwasher must be installed on a ‘solid’ level surface.
Electrical
- Machine Voltage/Amperage: 120V, 60 Hz, 10.6 Total Amps
- Connection: 3-prong plug with cord provided
- Circuit/Protector: 3-wire single phase, 120V, 60Hz, AC, on
a seperate 15 Amp circuit.
Note: Hard Water conditions will adversely affect
washability performance of your dishwasher. Hard water
conditions will also contribute to “Lime” (white film
substance) deposits and/or “Scaling” on the stainless
steel surface of the dishwasher tub and“Heater Element”
located in the sump underneath the removable filter
screen. To assist in minimizing these conditions, it is
recommended to periodically operate/rinse the inside of
the dishwasher (empty) using 1 cup of white vinegar (at
least once a week).
Water Pressure
For best operating results, incoming water pressure should
be between 10 and 145 psi (.05 and 10 bar). Incoming water
supply for the dishwasher is controlled by a ‘pressure switch’
application, so if available water pressure is low, dishwasher
fill time will be longer.
Once you open a supply line, (even if it’s closed
immediately thereafter) the water inlet hose will
be pressurized.
3
INSTALLATION INSTRUCTIONS
BUILT-IN INSTALLATION
If you specified a built-in installation, your dishwasher came
with the Built-In Hose Kit (Part# DWVBIHK) and Built-In Trim
Kit (Part# DWVTKBL).
CUTOUT FOR BUILT-IN
Water
Supply
Water
Inlet
Installation Location
- This dishwasher is approved for built-in installations.
- Air space requirements: Sides=3/16” (.48 cm),
Top/Bottom=1-1/8” (2.86 cm), Rear=2” (5.08 cm)
- The water inlet hose from the machine terminates in a
3/4” “female” connector. The water supply should there-
fore terminate in a similar “male” connector and should
have a stopcock close by in the pipe.
Water
Outlet
Min.
21-3/4"
Deep
Electrical
- Make sure the HOT water supply faucet connection is
within easy reach of the machine. The fill-drain hose
assembly is 5 Feet (152.4 cm) long.
Opening: Min. 23" Wide
Water Drainage
BUILT-IN
(side view)
- Standpipe Drain System: No point of the drain hose must
ever be placed higher than the top of the machine. If this
should ever happen, the functioning of the machine can
be affected.
Trim Kit
- Sink Drainpipe System: When routing the drain hose
through cabinets or walls, use a protective material such
as electrical or duct tape to cover sharp edges that could
damage the drain hose. Use a suitable clamp to se-
cure the drain hose to the “Y” branch or disposer. With
a sink drainpipe system, you may connect directly: 1) To
a disposer by following the manufacturers attachment
method. 2) directly to a “Y” branch tailpiece (available at
most hardware stores).
Drain
Connection
Dishwasher
3-Prong
Electrical
Installation Block
Supply
Connection
TRIM KIT DIMENSIONS
WATER DRAINAGE OPTIONS
Outlet
Hose Hanger
Width: 25 1/8”
Sink
Sink Drain W/ "Y" Branch Tailpiece
Width: 22 5/8”
Floor Standpipe Drain
4
INSTALLATION INSTRUCTIONS
COUNTERTOP INSTALLATION
If you specified a countertop installation, your dishwasher
came with a Quick-Connect Faucet Adapter Kit (Part#
DWVCTHK) that includes a fill and drain hose assembly that
is compatable with both male (exterior) and female (interior)
threaded faucet connections. If your existing faucet adapter
is not compatable with the Quick-Connect hose assembly
supplied, use the adapter supplied with the Quick Connect
Faucet Adapter Kit:
- If your faucet has a “male” type thread connection, remove
the second rubber washer and use only the standard
washer supplied inside the tap adapter (both 5mm thick).
- If your faucet has a “female” type thread connection, keep
the two rubber washers (both 5 mm) installed inside the
tap adapter.
Bleeder Button
Use with inside
threaded faucet
only
Push collar down
and slip faucet
adapter onto
faucet
Installation Location
The minimum height clearance required to install your
dishwasher on a countertop surface with overhead cupboards
is 18” (45.7 cm).
Follow These Steps
1. Screw the faucet adapter onto the faucet, then check for
leaks. (Use plumbing tape to eliminate leaks if necessary.)
2. Connect the open end of the drain hose to the Drain Hose
Connection at the rear of the dishwasher.
3. Connect the water inlet hose to the Water Inlet Connection
(Fig. 9) at the rear of the dishwasher.
4. Attach the Quick-Connect Faucet Adapter by pulling down
on the outer collar while pushing upwards on the faucet
adapter. When the Quick Connect snaps onto the adapter,
release the outer collar and it will lock into place. Check for
a correct fit.
5. Slowly open the hot water line. Examine all hose
connections for water leaks. Immediately close the water
supply and repair the hose connections if leaks are found.
6. If you are unable to successfully complete the countertop
installation yourself, please call our Service Headquarters
toll-free: 1-800-356-0766.
5
INSTALLATION INSTRUCTIONS
DISCONNECTINGYOUR DISHWASHER
When the cycle is complete, always relieve water pressure
from the inlet hose:
- Close the HOT water supply at the stopcock.
- Disconnect the Power Supply Cord
DO NOT LET CHILDREN DISCONNECT THE
DISHWASHER QUICK-CONNECT HOSE
ASSEMBLY. Close supervision of children is
always important around appliances.
For Built-In Installations
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found. Remove and clean the filters and
the water valves. Replace the inlet hose as needed to reduce
the risk of hose failure.
To relieve water pressure that’s inside the water
inlet hose, first close the water line (faucet). Then
press the Bleeder Button on the Quick Connect
Assembly until the flow of water stops.
For Countertop Installations
Release water pressure from inside the fill hose by pressing
the “red” Bleeder Button on the Quick Connect Assembly un-
til the water flow stops. Then, disconnect the Quick Connect
Hose Assembly from the faucet by pulling down on the outer
collar.
When the dishwasher is not in use, place/store the hose on a
hanger hose bracket or similar hanging device.
BEFORE DISCONNECTING THE QUICK-CON-
NECT ASSEMBLY FROM THE FAUCET, ALWAYS
RELIEVE WATER PRESSURE. Failure to do so
will result in back-pressure overspray. Back-
pressure overspray could cause severe burns
and/or scalding as the temperature of incoming
water could be very hot.
Appliances that are to be discarded must be made
unusable. Before discarding, remove the door to the
washing compartment.
6
USE AND CARE GUIDE
LOADING THE DISHWASHER
USING THE RIGHT DETERGENT
The dishwasher is designed to receive a standard “4 piece”
plate setting consisting of the following:
Use only detergent specifically made for use in dishwashers,
as other types will cause over-sudsing. If your detergent
is old and/or lumpy, throw it away. Old detergent loses it’s
washing power. Lumpy detergent won’t dissolve. The amount
of detergent you use depends if your water is “hard” or “soft”.
- 4 Dinner Plates
- 4 Bread & Butter Plates
- 4 Fruite Bowls
- 4 Cups and Saucers
- 4 Dinner Forks
- 4 Dinner Knives
- 4 Salad Forks
- 4 Teaspoons
- 2 Serving Spoons
- 1 Serving Fork
The recessed detergent area is located on the inside door
panel and will hold approximately 7 grams of detergent.
NOTE: Hard water requires more detergent to get dishes
clean. Soft water requires less detergent to get dishes
clean.
NOTE: For ease of loading/unloading large size
dinner plates from the dish rack it may be necessary
to (temporarily) remove the silverware basket. When
loading/unloading is complete, return the silverware
basket to it’s original position.
Put detergent in the recessed detergent area
located on the inside door panel
PreparingYour Dishes For Washing
- Scrape off all solid food particles from the dishes.
- Remove excessive quantities of oil or grease.
- Empty any liquids from glasses and cups.
- All dishes should be thoroughly rinsed before being placed
inside the dishwasher.
- Arrange all items with recessed or curved sections on a
slant to drain water away.
- Cups, pots, glasses etc. should be placed upside down.
USING A RINSING AGENT
NOTE: Dishes with dried-on foods are more difficult to
wash and may not come clean in a normal wash cycle.
You can help prevent unsightly spots on dishes and glassware
and reduce drying time by using a rinse agent.A rinse agent is
specially formulated to rinse away food and detergent residues
that can be left behind on your dishes. Used regularly, a rinse
agent will automatically provide you with cleaner dishes every
time you wash.
Your dishwasher is not a “waste disposal unit”,
clean off large particles of food sediments before
placing dishes in your dishwasher.
- First add the rinse agent into the Rinse Agent Measuring
Container that came with your dishwasher.
- To fill the rinse agent dispenser, unscrew the dispenser cap
located on the inside back wall of the washing tub. Use the
Measuring Container to slowly add the rinse agent into the
dispenser until it just reaches the bottom of the filling cap
inside of the dispenser opening. Replace the cap. The dis-
penser automatically releases approx. 90 cc of the rinse
agent into the final rinse water at the end of the wash
cycle.
7
USE AND CARE GUIDE
ECONO FEATURE
The “Econo” feature gives you the option of washing dishes
at “normal” incoming water temperature (usually between
130°F-140°F/54.4°C-60°C). When activated, the “Econo”
feature de-activates (by-passes) the heating element.
To activate this feature, push the “Econo” button on the
control panel.
Unscrew the Rinse Agent
Dispenser Cap, then use the
Measuring Container
- Push button “out”= the “Econo” feature is activated.
(“Saniwash” indicator light remains OFF). When the
“Econo” feature is activated, drying time for the dishes will
be increased.
(provided) to fill the dispenser
PRE-RINSE FEATURE
The “Pre-Rinse” is a convenience feature that allows
dishes to be rinsed, if you don’t have a full load ready to
be washed. (Preventing food from becoming dried/caked on
the dish surface). It is not necessary to add detergent to the
dishwasher during the Pre-Rinse cycle. However, due to the
short duration of the Pre-Rinse cycle (6 minutes only) make
sure the incoming water supply is HOT.
NOTE ABOUT DRYING
The dishes dry by a “convection” method only.
To speed-up the drying time, it is suggested to
leave the dishwasher door partially open after
the program is complete. This will allow hu-
midity from within to escape. Push the “Door
Open” button and the door pops open to a pre-
set convection drying position.
SANI FEATURE
The “Sani” wash feature gives you the option of washing
dishes at very high temperatures. When activated, the
“Sani” feature activates a heating element that will raise and
maintain the internal water temperature of the dishwasher to
151°F (66°C).
To activate this feature, push the “Sani” button on the control
panel.
- Pushbutton“in”=the“Sani” featureisactivated. (“Saniwash”
indicator light remains illuminated during the entire cycle).
Water temperatures this high can cause severe
burns/scalding. Always exercise extreme care
when opening and/or entering the dishwasher
during the Sani wash cycle.
8
USE AND CARE GUIDE
OPERATING INSTRUCTIONS
To OperateYour Dishwasher
1. Make sure the water inlet and drain hoses are correctly
PROGRAM SUMMARY/SELECTION
and securely connected.
2. Push the “Door Open” button to open the door.
PRE-RINSE
Water Temperature:
Incoming Water
(Tank Temperature)
6 Minutes
3. Place the dishes on the Dish Rack and cutlery (unsorted)
inside the Silverware Basket.
Program Duration:
Water Consumption:
0.84 gal. (3.2 liters)
4. Check to make sure that the rotating spray arm can turn
freely all the way around. If necessary, remove any
obstacles.
NORMAL/SANIWASH
Water Temperature:
Program Duration:
154°F / 68°C
35 Minutes
3.3 gal. (12.8 liters)
5. Fill the detergent in the recessed area on the door panel
Water Consumption:
(approx. 7 grams).
NORMAL/ECONO
Water Temperature:
6. Firmly close the door.
Incoming Water
(Tank Temperature)
35 Minutes
7. Open the hot water supply.
Program Duration:
Water Consumption:
3.3 gal. (12.8 liters)
8. Turn the Program Selector switch to the desired wash
program. (Pre-Rinse, Normal Wash, or Short Wash).
SHORT/SANIWASH
Water Temperature:
Program Duration:
Water Consumption:
154°F / 68°C
23 Minutes
2.5 gal. (9.6 liters)
9. Push the Power On/Off button.
- Push button “in”= Power ON
- Push button “out”= Power OFF. The Power Light will
illuminate, indicating the machine is receiving power.
SHORT/ECONO
Water Temperature:
Incoming Water
(Tank Temperature)
23 Minutes
10. The dishwasher stops automatically at the end of the
program. Both the Power Light and the and the Saniwash
Light will remain illuminated until the Power ON/OFF
button is switched OFF. NOTE: The dishwasher is
designed to stop if the door is opened accidentally
during operation.
Program Duration:
Water Consumption:
2.5 gal. (9.6 liters)
NOTE: At the beginning of each cycle, the dishwasher
always starts in the “drain” mode. This is because the
drain pump always retains a small amount of water (in the
sump) from the previous (last) cycle. This is necessary
to keep the pump primed. Therefore, don’t be alarmed
if a small amount of water being pumped out from the
drain hose prior to the start of the regular wash cycle.
THIS IS NORMAL.
11. When the cycle is complete, always relieve pressure on
the inlet hose by following the instructions on page 7.
12. After washing, dishes should be allowed to cool down for
approx. 15 minutes so they are not too hot to handle.
Dishes will cool quicker if door is slightly open.
13. After unloading the dishwasher, remove the Filter, clean
off any bits of food, and put the Filter back in it’s position.
9
TROUBLESHOOTING
COMMON PROBLEMS & SOLUTIONS
PROBLEM
POSSIBLE CAUSE
SOLUTION
Dishwasher will not start
- Dishwasher not receiving
electrical power.
- Check electrical connection
fuse/circuit breaker
- Door is unlatched
- Dishwasher not level
- Close and latch door
- Make sure dishwasher is installed
‘solid’ level surface
Dishes not clean
- Improper loading
- Arrange dishes so spray action
reaches all surfaces.
- Do not overload dishwasher
- Spray arm not rotating freely
- Make sure nothing (i.e. cutlery) is
obstructing spray arm rotation
- Make sure filter screen has not
become dislodged and is not
obstructing spray arm rotation
- Use more dishwasher detergent
- Do not use detergent that is hard or
caked
- Not enough detergent and/
or improper detergent being
used.
- Use only a recommended dishwasher
detergent.
- Excess food soil and liquids should be
removed from dishes before loading.
- Eliminate kink or bend from inlet hose
- Improperly prepared dishes
- Water inlet hose kinked/bent
due to improper installation
Chipping or breaking
glassware
- Improper loading of dishes
- Do not overload dish rack. Load
glasses on the upper rack only, not
over dish rack pins. Glasses loaded
over dish rack pins are not properly
supported and subject to damage.
Water remains in bottom
- A small amount of water (in
sump area) is normal.
- This is necessary to keep the pump
primed and is drained automatically at
the beginning of each cycle.
- Allow dishwasher to complete full
cycle.
- Excessive amount of water;
Cycle not completed
IFYOU NEED SERVICE
This Vesta™ appliance comes with a Limited Warranty
(please read the Limited Warranty Statement that came
with your dishwasher for complete details.) You’ll find many
answers to common problems in the Troubleshooting section
of this manual. If you read this section first, you may not need
to call for service at all.
- If you do need service, you can relax knowing that help is
only a phone call away. Call our Technical Service and
Assistance Department toll-free at 1-800-356-0766
Monday-Friday (8:00AM-5:00PM Pacific Time).
- Please have the model number and serial number of your
dishwasher ready when you call.
10
WARRANTY STATEMENT
V STA
LIMITED WARRANTY
This VESTA Dishwasher (Part# DWV303B) is warranted for one year from the date of purchase on MECHANICAL PARTS ONLY, when installed
and operated in accordance with the instructions in the manual. If the machine fails to operate due to any defects in material or workman-
ship it will be repaired at no cost to you at Westland Sales. Parts will be supplied at no cost during the warranty period for field repairs by
your installer or any authorized repair center. This warranty does not apply to installation costs. This warranty applies to the dishwasher
being used for private/family use ONLY. This warranty does not cover water damage of any kind. Only repairs that are attributed to normal
failure of the electronic and mechanical functions of the product are covered. Failure due to, but not limited to, abuse, negligence, impact,
fire, lightning, power failures and/or surges, rust, corrosion and water supply failures are not covered. Damage and/or repair to cabinets and
all exterior components including, but not limited to knobs, exterior wiring, doors, hinges, and gaskets are not covered.
Any representation of this warranty other than the terms herein is not binding on Westland Sales or it’s agents, nor shall they be liable for
any incidental, or consequential, damages. This warranty gives you specific rights, and you may also have other rights that vary from state
to state. All service questions can be answered by contacting Westland Sales directly. ALWAYS CALL WESTLAND SALES BEFORE REPAIRING
OR SHIPPING THIS DISHWASHER TO AVOID COSTLY REPAIRS DUE TO SIMPLE ADJUSTMENTS.
IMPORTANT RETURN INSTRUCTIONS
Your warranty depends on your following these instructions
In accordance with this Warranty, for the first twelve months from date of purchase, Westland Sales will repair the unit at no cost if it is de-
fective in material or workmanship providing it is returned to Westland Sales, freight prepaid, with PROOF OF PURCHASE (Pack well and ship
via Insured UPS).
1. CALL WESTLAND SALES AND RECEIVE AUTHORIZATION FOR THE RETURN.
2. Carefully pack the item in it’s original carton or other suitable box to avoid damage in shipping.
3. Before packing your unit for return; be sure to enclose:
a) your name, full address with zip code and telephone number,
b) a dated sales receipt or PROOF OF PURCHASE,
c) The model number of the unit and the problem you are having. (Enclose in an envelope and tape directly to the unit before the box is
sealed.
4. Westland sales recommends you insure the package (as damage in shipment is not covered by your warranty).
5. All shipping charges must be prepaid by you.
WESTLAND SALES
15650 SE 102nd Avenue, Clackamas, OR 97015
1-800-356-0766
LOCAL: 5036552563
11
™
Vesta DWV303
Automatic Compact Dishwasher
Westland Sales Corporate Headquarters : Clackamas, OR
Westland Sales Elkhart Operations: Elkhart, IN
Phone: 503-655-2563 Toll-Free: 800-356-0766
© 2003 Westland Sales
|