R
X348NT
PWR
PWR
TOUCH SCREEN 1-DIN 7 TFT LCD DVD PLAYER
MADE IN CHINA
Warnings and Precautions
Warnings
1
2
3
Only connect the unit to a 12V power supply with negative grounding.
Never install the unit where the operation for safety driving is restrained.
Never use the video display function in the front when driving to prevent the violation of laws
regulations and also to reduce the risk of traffic accident except using for rear view video camera.
4
5
Never expose the unit, amplifier, speakers to moisture or water to prevent electronic sparks or fires.
Please don't change the fuse in the power cord without professional guidance, improper fuse may
cause damage to this using unit or even cause fire.
6
7
Please power off the unit at once and send it back to the after-sales service center or the dealer/
distributor yo purchased from if one of the following symptoms is found:
(a)NO audio output; (b)NO image output;(c)Water or other obstacle enters the unit; (d)Smoking;
(e)Peculiar smell.
To ensure safe driving, please adjust the volume to a safe and comfort level in case of emergency
situations.
2
Warnings and Precautions
Precautions
1
2
Never disassemble or adjust the unit without any professional guide. For details, please consult any professional car shop/
dealer for inquiry.
If the front panel or the TFT monitor is squalid, please use a clean silicone cloth and neutral detergent to wipe off the spot.
Using a rough cloth and non-neutral detergent such as alcohol for cleaning may result in scratching or decoloration to the
applicant.
3
4
5
If any abnormal behavior of the unit is found, please refer to trouble shooting guide of this manual. If no relevant information is
found , please press the [RESET] key on the front panel to resume factory default.
If you have parked the car in hot or cold weather for a long time, please wait until the temperature in the car becomes normal
before operating the unit.
Using in-car heater in low temperature environment may result in beads coagulate inside the unit, DO NOT use the unit in this
situation, eject the disc and wipe off the bead on the disc. If the unit still doesn't work after a few hours, please contact with
after-sales service center.
6
7
8
No fierce impact to the LCD monitor when it is in open position for preventing the damage to any mechanisms inside.
To prevent the damage to the screen, avoid touching it with sharp objects.
The monitor employs auto motorizing mechanism, please don't push, pull, or swivel the monitor manually to prevent damage
to any mechanisms inside.
9
To provide a clear demonstration and an alternative for easy understanding to the operation of this unit, graphic illustrations
are used. However, these illustrations are some different from the actual images displayed in the unit.
10 During operation the unit," "is displayed if the particular operation is not available or illegal.
11 Operate the unit correctly according to this manual to prevent. Unnecessary problem. The guarantee won't be valid if the
problem is caused by inappropriate operation.
3
Electric Connection
TV ANTENNAPLUG
(Without TV tuner,
without this wire.)
CAR ANTENNA
GRAY
(RED)
FRONT RIGHT RCA OUT
FRONT LEFT RCA OUT
REAR RIGHT RCA OUT
(WHITE)
(BLUE)
GRAY
GRAY
(PURPLE)
(YELLOW)
(YELLOW)
(WHITE)
GRAY
GRAY
REAR LEFT RCA OUT
VIDEO OUT
BLACK
BACK CAR VIDEO IN
AUX LEFT IN
BLACK
BLACK
BLACK
Parking Brake Light (-)
Back car detecting wire
(Gray)
(RED)
AUX RIGHT IN
VIDEO IN
(YELLOW)
(Brown)
White/Black
White
To front left
speaker
Connect control for antenna or remote control for amplifier
Ignition key
switch
(Blue)
(Red)
FRONT.L
Gray/Black
Gray
To front right
speaker
ACC wire
FRONT.R
REAR.L
Battery wire (Yellow)
Green/Black
Green
To rear left
speaker
Car fuse box
(main fuse)
Ground wire(Black)
Light wire
(To car chassis)
Battery
Purple/Black
Purple
To rear right
speaker
(Orange)
REAR.R
4
Installation
Before installing the receiver permanently, fit it in the approximate place in your car ,and connect the
equipment according to the speakers and electrical connections. When
your system is operated properly,(preferably with the
car engine running), follow the instructions
for permanent installation
of your system.
INSTALL THE UNIT
1)Install half sleeve, can be with or
without adapter. It will fit better
with adapter.
2)Bend over some tabs to secure
the half sleeve inside of dash.
3) Support strap to be strutted
under dash, secure this strip to
avoid skipping of disc.
2)Bend over tabs
of half sleeve
(supplied)
1) Adapter
(not supplied)
Half sleeve
(supplied)
REMOVE THE UNIT
Insert removal wrench into the small
gap on the right side of the unit and pull
the unit slightly out on the same side,
then release the wrench. Repeat the
same action for the left side. By now,
you can remove the unit and unplug
the wires connector.
3) Two wrenches for releasing
the unit (supplied)
5
General Features
18
17
16
19
15
Adjust angle
Stop/Clock
RPT/ST
SRC
RESET
AUX IN
14
13
L
EJECT
BT
V
MIC
IR
PWR
MUTE
BAND
1
2
3
4
5
6
7
8
9
10 11 12
6
General Features
Remote Control
18
17
16
Loading and replacing the battery
19
15
Stop/Clock
RPT/ST
Adjust angle
SRC
RESET
AUX IN
14
13
L
EJECT
BT
V
MIC
IR
PWR
MUTE
BAND
Pull out
1
2
3
4
5
6
7
8
9
10 11 12
1
VOL/SRC/PWR Button: Rotate the VOL button to adjust the
volume; press it to make confirmation./Play source switch.
Notes of remote control using:
2
3
5
6
7
8
9
MIC.
4
1)Aim the remote controller at the remote sensor on the unit.
2)Remove the battery from the remote control or insert a
battery insulator if the battery has not been used for a
month or longer.
3)DO NOT store the remote control under direct sunlight
or in high temperature environment, or it may not function
properly.
/
[
Signal received window.
]/[ ]Button: Rewind, Last chapter/Forward,Next chapter.
SD Slot.
To eject the DISC.
MUTE/[ ] Button: Mute/Answer.
BAND Button: Band switch/Radio mode is random play.
BT Button: Switch to BT function directly.
110
4)The battery can work for 6 months under normal condition.
If the remote control can't work, please change the battery.
5)Use(button shaped) lithium battery(CR-2025)only.
6)DO NOT recharge, disassemble, heat or expose the battery
in fire.
11 EJECT Button: To eject the DISC.
12 AUX IN
13
USB Port.
14 Reset Button.
15
[
]Button: Display Open/Close.
16 Adjust angle Button: Display position Adjustment.
17 TFT-LCD screen.
7)Insert the battery in proper direction according to the(+)
and ( - ) poles.
18 ST/RPT Button: Sound track switch/Repeat.
19 CLOCK/STOP Button:Clock/Stop.
8)Store the battery in a place where children cannot reach to
avoid risk of accident.
7
Remote Control
Button and Function
2 [BAND/RDM] Button: Band switch/Play randomly
[APS/PRG] Button: Scan/Program
[ST/RPT] Button: Stereo switch/Repeat
PWR
Mute
SRC
REC
Sub-T
1
2
3 [ ]Button: Play/Pause
[
R/L
N/P
Band
RDM
]Button: Stop
[Setup] Button: Menu setting
[Title] Button: Title Menu
Language
Angle
7
6
SEL
APS
PRG
CLK
EQ
S T
[ENTER] Button: Play/Confirm
[ ][ ][ ][ ]Button: Up/down/left/right button
RPT
AF
[
] Button: Ring on
[OSD/ Id3] Button: Screen Display/ Select chapter
] Button: Ring off
4
3
Enter
TA
[
Setup
Title
PBC
PTY
[0~9]Button:0~9
[GOTO] Button: GOTO search
[RO/SN] Button: Radio scan
5
6
7
2
3
1
ABC
DEF
4
5
4
5
6
OSD
GHI
JKL
MNO
[AF] Button: Search stations automatically
[TA] Button: Traffic broadcast
[PTY] Button: Program style
I
D3
7
8
9
PQRS
WXYZ
TUV
0
RO/SN
#
Goto
[
[
]Button: Forward/Next chapter
]Button: Rewind/Last chapter
*
10+
[+/-]Button: Increase/recluce volume
[SEL] Button: System setting
[CLK] Button: Clock display
Note: This unit doesn't have RDS function, AF/TA/PTY neither.
This unit doesn't have bluetooth function, [ ]/[ ] neither.
If the unit hasn't some functions , some buttons won't be affected.
[EQ] Button: Sound effect
1
[PWR] Button: Power
[N.P/ANGLE] Button: Video switch/Angel Adjustment
[R.L/LANGUAGE] Button: Left/right sound track switch
dialogue language.
[REC/Sub-T]Button: Transfer recording/Language switch
[MUTE] Button: Mute
[SRC] Button: Play source switch
8
Play operation
Flex screen(
)
Adjust angle
Stop/Clock
RPT/ST
Open screen: Press [ ] to open.
Close screen: Press [ ] to close.
Note:
If the screen stop when out press[ ] to hide the screen, then press
[
] again the screen will out.
When power off, the screen will hide.
Eject
EJECT:
Press[ ] to eject the disc.
Note: About 10 seconds after the disc ejected ,if not taken out, the
disc will be absorbed in again.
SRC
RESET
AUX IN
Volume
L
EJECT
BT
V
MIC
IR
Increasing Volume:
Rotate the VOL button in counterclockwise direction.
PWR
MUTE
BAND
Decreasing Volume:
Rotate the VOL button in anticlockwise direction.
ON.OFF
Stop/Clock
Press [PWR] button shortly will turn the unit on. Hold [PWR]
button down will turn off the unit.
NOTE: When the power is on, the screen enters RADIO mode
automatically; press [ESC] button to go back to the main menu;
press [SRC] button shortly to switch to other modes.
STOP:
Press [STOP] button to stop when DVD playing.
CLOCK:
Press [CLOCK] to switch between radio frequency and
clock, when radio playing.
9
Play operation
Display position Adjustment
MUTE/
MUTE: Short press this button to mute the sound, short press
MUTE button again or press any other button to resume
the normal listening.
For smooth adjustment, make sure that you return the lateral
angle to the neutral position and then adjust the tilt angle.
Avoid physical shock on the display.
Channel seek: In BT mode, when call comeing, press this
button can answer.
Tilt angle
Stop/Clock
RPT/ST
Adjust angle
Press [ADJ] button ,it can adjust the
screen angle gradually.
The unit has 4 grades
Stop/Clock
RPT/ST
Adjust angle
Stop/Clock
RPT/ST
Adjust angle
for adjustment ,and each time you
press the button ,it can move one
grade down along indication; it can
resume up along indication.
CLOCK
STOP
ST
ADJ
RPT
Adjust angle
SRC
RESET
AUX IN
L
V
MIC
EJECT
BT
IR
PWR
MUTE
BAND
When you turn on the unit again, the angle
will be the same as the last angle that
you set.
ADJ ANGLE
Stop/Clock
RPT/ST
Adjust angle
CAUTION
Do not place any object on
the display forcefully, or
subject it to undue force.
Do not move the display
forcibly.
The monitor's movable range
may be limited by the type of
car, a position where the
display is mounted, etc.
SRC
RESET
AUX IN
L
EJECT
BT
V
MIC
IR
PWR
MUTE
BAND
10
Setup Operation
MENU
Video setup
ENTER MENU: Press [MENU] button, then touch setting button, it
Bright Color Contrast Tint
will show in screen follows:
Vmode
Video mode:
STAD
USER
SOFT
VIDEO
Menu operation
BRIGHT
COLOR
14
14
BRIG
CONTRAST 13
TINT
VMODE
Touch [
Touch [
Touch [
]/[
]/[
] to choose menu.
]to adjust parameter.
15
STND
] to back main menu.
Audio setup
Audio setup Bass Treble Balance Fader
setup between 0~14.
Audio mode:
EQ setting
AUDIO
NORM
FLAT
POP
BASS
0
Menu operation
TREBLE
BALANCE
FADER
EQ
-
07
06
06
R
R
Touch [
Touch [
Touch [
]/[
]/[
] to choose menu.
]to adjust parameter.
FLAT
CLAS
ROCK
] to back main menu.
System setup
Loud ON and OFF
Beep ON and OFF
Time Adjust press [
BASIC mode:
BASIC
] or[ ] button to select hour/
Menu operation
LOUD
BEEP
OFF
ON
minute then press [ ]or [ ]button to setup.
CLOCK
00:00
Touch [
Touch [
Touch [
]/[
]/[
] to choose menu.
]to adjust parameter.
] to back main menu.
11
Radio Operation
Select station
Adjust angle
Stop/Clock
RPT/ST
Press [AS/PS] button
Seek Tune:
In radio playing mode, holding down the [AS/PS] icon will
seek and store strong frequency stations automatically.
Note: FM band can store 18 stations; AM band can store 12 stations.
AF
TA
PTY
Browse station
Press [SCAN] button
Press [SCAN] button to scan the existing station.
SRC
RESET
AUX IN
L
EJECT
BT
V
MIC
IR
PWR
MUTE
BAND
Band Tune
Manually Tune
Note: If the unit doesn't have RDS function, the touch-screan
won't show "AF, TA and PTY".
Press[ ] button: adjust to higher frequency.(such as
87.5,87.55...)
Press[ ] button: adjust to lower frequency(such as
105.5,105.0...)
Band
Press [BAND] button to transfer band.
Automatically Tune
Holding down the [ ] button: search higher frequency
station, and will stop when meeting one.
FM1
FM2
FM3
Holding down the [ ] button: search lower frequency
station, and will stop when meeting one.
AM2
AM1
12
Radio Operation
AF(Alternative Frequency)
Press AF and then press[ ],the machine will scan signal get
the best frequency of the local radio station. If meet a stronger
signal of the same program. letter TP will appear on LCD,
and unit will automatically choose the stronger signal sought.
Before auto scan the radio station, please turn off AF
firstly.
Only remote control (
page8)
TA(Traffic announcement)
Press TA, the unit will prior to seek the traffic information. If the
machine receives the traffic information, it will choose this
signal and quit other radio signal or CD program. If press TA
again, other program will recover and the traffic information
program will quit.
Only remote control (
page8)
PTY(Program type)
Press PTY, the unit will begin to receive program as news,
current affairs ,music, etc. The unit will seek the program
automatically and will quit CD player if it gets the right program.
If press PTY again, PTY function will quit and other program will
play as before.
Among AF, TA and PTY, TA has the absolute priority to be chosen.
Only remote control (
page8)
Note: If the unit is without RDS function, please skip this page.
13
Sound Operation
L/R
L/R
E
Play/pause
In play mode, press [
mode.
] button to switch to play or pause
Five direction button: In play mode, you can touch[ ][ ]icon to
choose music, touch [E] to play music.
Select chapter or section: In the DVD mode, press [ ] to
TIT
choose last chapter, press [ ]to choose next.
Forward: Hold [ ] button down;
Rewind: Hold [ ] button down.
Title: In play mode, press [TIT] on the screen or remote control to
back to the title menu, and re-select the items needed.
RPT
L/R
RPT: In the play mode press[ RPT ]button then can transit among
R/L: In VCD/CD/DVD mode, press [R/L]on the screen or remote
control to switch among mono L mono R or stereo.
the following status.
REP ALL
REP ONE
REPEAT OFF
14
SD/USB Operation
USB/SD play operation
CLOCK
STOP
ST
ADJ
PLAY/PAUSE:
Adjust angle
RPT
Press [
Select:
Under USB or SD play, press[
] button to play or pause.
SRC
RESET
AUX IN
L
EJECT
BT
V
MIC
IR
PWR
,
MUTE
BAND
,
]can select tracks.
REPEAT
Press [ST/RPT] button first to repeat the playing track
RPT OFF
RPT DIR
RPT ONE
RPT ALL
BAND:
Press [BAND] button to play the disc randomly.
RDM OFF
RDM ON
USB/SD mode
USB/SD mode
Inset USB/SD,the play will to the USB/SD playing mode
antomaticly.
15
Bluetooth
The Bluetooth is wireless mode of transmission in short
distance. Through Bluetooth function, the DVD unit establishes
connection with Bluetooth handset. And then, these units can
realize mutually controling and file transfering.
Paring
Phone set pairing step as follows:
A: Turn on Bluetooth, then
touch On/Off icon to turn
on this function.
NO.2
Choose the Bluetooth Mode
B: Turn on handset's Bluetooth
function .
Method :
A: Press the [SOURCE] button, to
return to main menu..
C: When the mobile phone
set finds the signal, input
pairing number. Initial Pairing Code No. 0000
B:Exhales the main menu, choose
the Bluetooth to enter the
Bluetooth mode.
D: After pairing, TFT screen shows pairing succeed and
quit the pairing.
NO.1
Working mode of Bluetooth
Bluetooth has the following functions:
A: Paring
Make DVD Bluetooth function as handset's
facility through pairing.
NO.1
-
-
B: Connecting
After connecting with the handset,
you can operate the mobile phone through DVD unit
(such as H,F, call, call record etc.)
NO.2
16
Bluetooth
Mobile phone
C: Touch Transfer icon can switch to phone answer mode.
Touch it again can return to Bluetooth function of the unit.
Remarks: Some mobilephone can't support this switch function.
After connected, you can make phone call through, touch
screen or phone record.
A: Making mobile phone call
After making phone call, the [ ]will shining.
13590205862
B: Making touch screen call
Input the numbers on the screen, press [ ] icon can correct
the numbers;
Press [ ] icon to answer phone call;
Press[ ] icon to cancel or hang up.
13590205862
Hang up
You can press the [ ]button to hang up.
13590205862
Answering
Answering functions as follows:
A: After connected, the unit can use the telephone function.
B: When there is a phone call, the Bluetooth will switch to
phone function and show the calling number automatically.
Note: If the unit does not have this function, pls skip it.
Some models of mobile phones are not supported by the
Bluetooth module of this unit.
17
TV Operation
Without touch function, without these icons.
CLOCK
STOP
ST
ADJ
Adjust angle
RPT
SRC
RESET
AUX IN
L
EJECT
BT
V
MIC
IR
PWR
MUTE
BAND
TV operation
You need install TV antenna, when receive program.
TV mode:
Press [SRC] to enter main menu, then press TV icon on
TFT screen to enter.
Channel search:
Press [APS] or press [AMS] to search and store TV station
automatically.
Direct Channel Selection:
(Only for remote control)
Note: If the unit does not have this function, pls skip this page.
Enter a channel number by pressing [0]to[9].
18
Accessories
External view
External view
........ Number of items
........ Number of items
1
3
............1
............2
2
............1
The use of any accessories except of those provided might
result in damage to the unit .Make sure only to use the
accessories shipped with the unit ,as shown above.
19
Troubleshooting
What appears to be trouble is not always serious. Please check the following points before calling a service center.
Familiar characters and their meanings
Characters
Causes
Remedies
Clean the disc or change the disc.
Insert the disc correctly.
Insert a disc.
Disc is too dirty.
Disc is inserted upside down.
No disc in the unit.
NO Disc
Disc is extreme dirty.
Clean the disc or change the disc.
Insert the disc correctly.
Bad Disc
Disc is inserted upside down.
The disc is not compatible with
the unit.
Unkown Disc
Clean the disc.
Clean the disc.
The disc's region code is not the
same as the unit's.
Region Error
Disc transparence fault press disc Then change the angle and inject
button long time exit.
Disc inject dead
again or change another disc.
21
Troubleshooting
General problems
Symptoms
Causes
Remedies
Install a new fuse with correct rating.
Install a new fuse with correct rating.
Reset the unit.
The fuse of the unit has been broken.
The unit cannot be
powered on.
The fuse of car battery has been broken.
False operations and etc.
Battery has been exhausted.
Change the battery.
Remote controller does
not work.
Battery is not installed correctly.
Install the battery correctly.
Correct the connection according to(Electrical
Connections Overall Diagram).
Audio output connection is not correct.
Adjust the volume to the optimum level.
Check the speakers.
The volume level is set to the minimum level.
The speakers have been damagedl.
No sound comes out or
it's hard to hear.
Adjust the balance of audio channel outputs. Please
refer to (Audio control).
The audio channel outputs are not balanced.
The speaker cord is contacted with the
bodywork.
Use insulating cord for connection.
Use original copy disc.
Piratic disc is used.
The speakers power rating does not fit into
the unit output power.
Change the speakers.
Poor sound quality or
sound distortion.
Correct the connection according to(Electrical
Connections Overall Diagram).
The speakers are connected incorrectly.,
The speaker cord is contacted with the
bodywork.
Use insulating cord for connection.
User preset information is
lost when ACC is off.
Correct the connection according to(Electrical
Connections Overall Diagram).
ACC and BATT are connected incorrectly.
22
Troubleshooting
TFT Monitor
Symptoms
Causes
Remedies
No image appears on the
monitor and warning
information is shown at
all times.
Correct the connection according to
(Electrical Connections Overall Diagram).
Incorrect connection of Breaking wire.
The color system of DVD disc is not
suited with the monitor.
Adjust the color system of the DVD disc
or the monitor.
The actual color system is not the same
as the marked color system on the label
for some piratic discs.
Use original copy disc.
Abnormal display like
as pulsatile stripes on
the image and on.
The video cord is broken.
Change the video cord.
The video cord is not connected correctly.
Connect the video cord correctly.
Turn off the power and then turn on the
power again, or change to other playing
source and then go back.
Characters are
abnormal.
False operations.
23
Troubleshooting
Radio Tuner
Symptoms
Causes
Remedies
Correct the connection according to
(Electrical Connections Overall Diagram).
Auto antenna is not extended completely.
It's hard to receive
stations.
Correct the connection according to
(Electrical Connections Overall Diagram).
Auto antenna is not connected with the unit firmly.
LOCAL function is on.
Close the LOCAL function.
Mp3 playback
Symptoms
Causes
Remedies
Change the disc.
Disc is scratched.
Disc is too dirty or wet.
Clean the disc.
Disc cannot be played
back.
Clean the pickup with cleaning disc.
The pickup is dirty.
Disc is inserted upside down.
Insert the disc correctly.
Change the disc.
Disc is scratched.
Disc is too dirty or wet.
Clean the disc.
Interruption occurred during
playback.
Change the disc.
Some contents are damaged.
Disc is not recorded correctly.
Record the disc again.
MP3's name cannot
be displayed correctly.
Use the regular characters.
The name of Mp3 is not regular.
24
Troubleshooting
DVD player
Symptoms
Causes
There is a disc in the unit already.
Disc is scratched.
Remedies
Disc cannot be inserted.
Eject the disc then insert another one.
Change the disc.
Disc is too dirty or wet.
Clean the disc.
The pickup is dirty.
Clean the pickup with cleaning disc.
Change the disc.
Disc is not compatible with the unit.
Parental lock class is too high.
Disc memory less than 120M.
Disc is inserted up side down.
Disc cannot be played back.
Change the parental lock class.
Choose the disc of memory more than 120M.
Insert the disc correctly.
The disc 's region code is not the same
as the unit 's.
Change the disc.
Change another disc containing subtitle files.
Subtitle cannot be shown.
There is no subtitle file in the disc.
There is only one audio language/subtitle
in the disc.
Change another disc containing multi-language
audio or subtitle.
Audio language/subtitle
cannot be changed.
There is just one view angle in the disc.
Change another disc containing multi-angle.
Select another segment to play back.
View angle cannot be
changed.
Multi-angle view is not available for the
segment playing back now.
The unit is compatible with copy system; hence
some discs contained the informationof copying
prohibited cannot be played back.
The disc is protected by the copyright.
Image distortion.
PBC is invalid when playing
back VCD.
The disc does not support PBC.
Change another disc with PBC function.
Close PBC function.
Repeat playback or GOTO search
is invalid when playing back VCD.
PBC is on.
25
Specifications
Specifications subject to change without notice.
DISPLAY UNIT
RECEVING FREQUENCY FIGURE
FREQUENCY
Liquid crystal panel.........................................7 inches wide
Display weight ...........................................................1.7kg
Number of pixels............................................33,6960 pixels
Display method........................Transparent color filter format
Drive method....................................TFT (thin film transistor)
active matrix format
Auto Tiny
Stepping Stepping
AREA
BAND
RANGE HZ
87.5-108.0M
522-1620K
KHZ
KHZ
100
FM
AM
50
EUROPE
9
9
87.5-107.9M
530-1710K
FM
AM
FM
AM
200
10
200
10
AMERICA
Light source.....................................................internal light
(built-in small fluorescent lamp)
87.5-108.0M
100
10
100
10
SOUTHA MERICA
520-1620K
87.5-108.0M
65.0-74.0M
522-1620K
GENERAL
50
100
30
9
1
2
FM
Operating power...................................12 Volts DC, negative
ground
RUSSIA
30
9
FM3
AM
%10THD output wiring........................Designed for using four
speakers only front and rear
channels cannot be combined
in use with 2speakers.
Load impedance.................................compatible 4 to 8 ohm
speakers
Fuses............................................................ .........10 amp
Dimensions....................... 52.5cm(L)x26.0cm(W)x29.3cm(H)
Weight........................................................................2.5Kg
26
1 Year Limited Manufacturer Warranty -
XO Vision warrants to the original retail purchaser of this product that should this product have any defect,
under normal conditions, such defect(s) will be repaired or replaced with new or reconditioned product
(at the Company's option) without charge for parts and repair labor.
If said product is out of stock, XO Vision has the option to replace it with a similar product or issue a refund at our discretion.
This warranty only covers manufacturer defects and must be returned to company in original condition.
Proof of Purchase is required. This Warranty does not cover the costs incurred for installation, removal, product damages
(i.e. discs, tapes, etc.) or reinstallation of the product.
This warranty is void if company deems the unit to have been damaged through modification, improper installation,
negligence, misuse, or tampering with the Serial number and/or bar code of the unit. This warranty is a limited warranty
for repair/replacement of product if it falls under the above conditions. XO Vision is never responsible for more than the
purchase price of the product.
XO Vision encourages customers to contact the retailer first and only then contact XO Vision for warranty support.
Customer is responsible for shipping the product to us; we cover shipping back to the customer.
In your email, please include the model number, date and place of purchase and the problem. Thank you for purchasing XO Vision.
OWNER'S MANUAL
Before installation and operating the unit please read
this manual thoroughly and retain
it for future reference
|