TUMBLE DRYER
TCE 7127 W
0
6’0
D
K
F
H
Unpacking: see page 15
INSTRUCTION BOOKLET
GB
125981701
Contents
Something Not Working
Service and Spare Parts
Customer Care
12
12
13
13
For the User
Important Safety Information
2
• Installation
• Child Safety
• Use
Guarantee Conditions
Adjusting the level of conductivity
14
Your New Tumble Dryer
Description of the Appliance
The Control Panel
4
4
5
For the Installer
Installation Instructions
Technical Specifications
15
15
• Programme Chart
• Low Temperature Button
• Buzzer Off Button
• Start Button
• Programme Phase Indicator Lights
• Programme/Time Selector Dial
5
5
5
5
5
6
• Unpacking
• Positioning
• Stacking kit (optional accessory)
• Door reversal
• Electrical connection
15
15
16
16
16
Programme Chart
7
8
Operating Sequence
Hints & Tips on Drying
Maintenance and Cleaning
9
10
• External cleaning
• Cleaning the door
• Cleaning fluff filters
• Cleaning the condenser unit
• Emptying the water reservoir
• Cleaning the air intake grille
• Cleaning the drum
10
10
10
10
11
11
11
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
Your New Tumble Dryer
This tumble dryer will give your wash that soft, relaxed feel whatever the weather.
Extremely high quality standards both during development and manufacturing
guarantee a long service life for your appliance.
Maximum economy in the operation of your dryer is achieved through very frugal
electricity consumption and short drying times.
Energy saving tips
• When the appliance is to be scrapped, cut off the
power supply cable and make the door closing
device unusable to prevent young children from
being trapped inside.
To save energy we recommend that you follow these hints:
• Try to load the maximum capacity of the machine
as small loads are uneconomical.
• Help to keep your country tidy - use authorised
• Always load well spun laundry. The higher the spin
speed, the lower the electricity consumption and
the shorter the drying times.
disposal sites for your old appliance.
How do we help to protect the environment? We use
recycled paper!
• Do not over-dry laundry, this avoids creasing and
saves energy.
•
Old appliance
• Clean the filters regularly to avoid excessive drying
times and high electricity consumption.
The symbol
on the product or on its packaging
• Ventilate the room well. The room temperature
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by in appropriate
waste handling of this product. For more detailed
should not exceed +35°C during drying.
In the interest
of the environment
• Materials marked with the symbol
are recyclable.
• Check with your local Council or Environmental
Health Office to see if there are facilities in your
area for re-cycling this appliance.
information about recycling of this product, please contact
your local city office, your household waste disposal
service or the shop where you purchased the product.
Description of the Appliance
01 Worktop
3
1
02 Programme chart
03 Control panel
04 Fluff filters
05 Rating Plate
06 Condenser unit
07 Water reservoir
08 Adjustable feet
2
7
4
5
4
8
6
4
The Control Panel
1
2 3 4 5 6
7
1Programme Chart
5Start button
This will help you to select the correct programme
for drying.
Press this button to start the dryer after having
selected the programme and the options.
The relevant light will stop flashing. If you have
chosen a delayed start, the machine will begin the
countdown.
2Low Temperature
Button
Pressing this button allows drying to be performed at
a lower temperature, for delicate items.
The corresponding pilot light comes on.
This option can also be used for time controlled
drying.
If the door of the appliance or the small door at
the bottom is opened while the programme is
running, this button must be pressed again after
closing the door in order to restart the programme
from the point at which it was interrupted.
This button must be depressed also after a power
failure and after having re-inserted the water
reservoir, if it has been emptied in the middle of a
The dryer heats at 1400 W instead of 2200 W.
If the button is not pressed, drying is performed at
full power (2200 W).
programme after lighting up of light
.
In both cases the light of the Start/Pause button
flashes to remind you that the start button needs to be
pressed again.
This option cannot be selected with QUICK DRY
.
3QUICK DRY Button
By depressing this button the drying time is reduced
in the following COTTON programmes:
6Programme Phase
Indicator Lights
• EXTRA DRY
• READY TO WEAR
• STORE DRY
These lights indicate the various phases of the
programme as they are being performed.
“Drying” light
The corresponding pilot light comes on.
This option cannot be selected with LOW
This light indicates that the appliance is in the drying
phase.
TEMPERATURE
function.
“Cooling” light
4Buzzer OFF Button
A buzzer sounds by depressing the push buttons
during the anti-creasing phase, at the end of
This light indicates that the appliance is in the
cooling phase. At the end of drying, there is a
10 minute cooling phase to cool the laundry.
programme and when the water reservoir is full.
Press this button when selecting the programme if
you wish to switch the buzzer off during the anti-
creasing phase. The corresponding light illuminates.
“End of programme” light
This light is on at the end of the cooling phase,
during the anti-creasing phase and at the end of the
programme.
5
“Filter cleaning” light
7Programme/Time
Selector Dial
This light illuminates at the end of the programme to
remind you that the filters must be cleaned.
Allows you to select electronically controlled or time
“Water reservoir full” light
This light comes on at the end of the programme to
remind you that the water reservoir must be emptied
out. If this light illuminates during a programme this
means that the water reservoir is full. The buzzer
sounds, the programme stops, the light of the
Start/Pause button flashes.
controlled drying.
Turn the dial to the required programme or time.
Electronically controlled drying (automatic)
The appliance runs these programmes with the help
of probes which detect the degree of dampness of the
laundry.
Simply select the programme according to the type of
laundry and degree of drying required.
This light comes on also when the water reservoir is
not inserted correctly.
“Condenser cleaning” light
Time controlled drying
It comes on every 80 cycles to remind you that the
condenser must be cleaned
Can be used to finish off drying if necessary.
Select the 90 or 60 minute programme for cottons or
the 30 minute programme for synthetics.
To cancel a programme which is running, turn the
programme selector dial to “0”.
At the end of drying, turn the selector dial to “0”
before removing the laundry.
6
Programme Chart
Automatic drying (electronic programmes)
Degree of drying
Type of laundry
required
Max-load (1)
Programme
extra dry
ready to wear
store dry
slightly damp
iron dry
wring dry
A
B
C(*)
D
E(*)
F
6 kg
6 kg
6 kg
6 kg
6 kg
6 kg
Cotton
extra dry
store dry
iron dry
3 kg
3 kg
3 kg
G
H(*)
J
Synthetics
K
L
Jumpers
baby dry
dry fresh
2 kg
Jackets, trousers,
dresses, skirts.
1 - 4 garments
(*) According to CEI 1121 Standards.
• Baby cycle “K” is a special programme for jumpers to be dried “ready to wear”.
• Dry fresh “L” is designed to clean and freshen garments labelled “dry clean only” and “hand wash” at home,
in your tumble dryer, using the special product available on the market.
Time controlled drying
Programme
selector dial position
Type of laundry
Cotton
Drying time
Max-load (1)
90 min
60 min
30 min
6 kg
6 kg
3 kg
90’
Cotton
60’
30’
Synthetics
(1) Never overfill the drum (do not load large quilts, for example).
Drying times vary according to:
• The type of laundry
• The size of the load
• The degree of spinning prior to drying.
• The degree of of dryness required
Fresh & Cool
This position on the programme selector dial can be used to freshen the laundry (e.g. to remove a persistent
odour of moth-balls).
Load
It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the
following guidelines:
• cotton, linen: drum full but not too tightly packed;
• synthetics: drum no more than half full;
• delicate fabrics: drum no more than one third full.
7
Operating Sequence
All drying programmes end with a 10 minute
cooling phase light is on).
You may remove the laundry after this phase.
The lights and illuminate.
Before using your tumble dryer for the first time, we
recommend to place a few damp cloths inside the
appliance and dry for 30 minutes.
There may be dust inside a brand new tumble dryer.
,
Drying
8. If the laundry is not removed at the end of the
cycle, the dryer performs an anti-creasing phase
(duration: 30 minutes maximum).
1. Connect the appliance.
2. Open the door (see picture).
If you do not remove the laundry, the dryer will stop
automatically at the end of the anti-creasing phase.
Lights
,
and
remain lit and the buzzer
sounds every 10 seconds for 2 minutes.
The light of the “START/PAUSE” button goes
off and a flashing zero appears on the display.
9. Turn the programme selector dial to “0”; all the
P1149
P1108
lights go out. The appliance is switched off.
Remove the laundry.
3. Load the items one at a time, shaking them out
loosely.
If you open and then close the door before
turning the selector dial to “0” all the lights
corresponding to the phases making up the
performed programme come on and the
display shows the duration of the programme.
4. Close the door. Please check the laundry does not
get caught between the door and filter.
5. Select the drying programme or time. The lights
,
and
come on. The light of the
“START/PAUSE” button flashes and the
display shows the duration of the programme.
After each use
6. If required, press the low temperature button
and/or the “Buzzer OFF” button or the “Quick
• Clean the filters (see page 10).
• Empty the water reservoir (see page 11).
drying” button
.
7. Press the “START/PAUSE”
button the
corresponding light stops flashing and drying
starts.
Important!
If the drying programme has to be stopped before it
reaches the end, we recommend that you turn the
Only the light
remains lit. If you have selected
the delayed start, the machine begins its
countdown.
programme selector dial to position
and wait until
the end of this cooling phase before removing the
laundry. This will avoid a build-up of heat inside the
appliance.To do this first turn the dial to “0” and then
If the programme selector dial is turned to another
position, when the machine is running, the buzzer
will sound, the programme phase indicator lights
will flash.
to
and depress “START/PAUSE” button
.
Modifying the programme
The drum turns alternately in both directions
during drying.
To change a programme which is running, first cancel
it by turning the programme selector dial to “0”.
Select the new programme and press the
“START/PAUSE” button.
8
Hints & Tips on Drying
Before placing articles of laundry in your tumble
dryer, check the care labels to ensure they are
recommended for tumble drying.
• Always load well spun laundry. The higher the spin
speed the lower the electricity consumption and the
shorter the drying time.
• DO NOT load dripping wet laundry into the dryer.
Roll the article in a towel or spin to remove excess
water.
Care Labels you may find on your laundry
may be tumble dried
• Close poppers and zips and fasten any buttons.
normal drying (high temperature)
delicate drying (low temperature)
do not tumble dry
• Sort the laundry. Separate synthetics from
cotton/linens, and dry separately.
• Remove the laundry immediately after the
programme has finished.
• Use a fabric conditioning sheet to reduce static. We
recommend the sheet is pinned to an article of
laundry (using a safety pin).
Do not overload the appliance.
Here is a list of the approximate weight of some
common laundry items.
• Mix the load i.e. large and small articles.
• When drying large items such as sheets, we
recommend you periodically stop the dryer to
redistribute the load.
Sheet
700 to 1000 g
Pillowcase
Tablecloth
Table Napkin
Kitchen Towel
Linen Hand Towel
Hand Towel
Bath Towel
Bathrobe
100 to 200 g
400 to 500 g
50 to 100 g
DO NOT use the tumble dryer to dry the following:
• Articles contaminated with inflammable substances
e.g. petrol, cleaning solvents, cooking oil, fats or
hair lacquer.
70 to 120 g
100 to 150 g
150 to 250 g
700 to 1000 g
1000 to 1500 g
200 to 300 g
150 to 200 g
• Woollen and synthetic/wool mixtures unless the
item is labelled as suitable for tumble drying.
• Very delicate articles such as silk.
Shirt
Apron
• Very large and bulky items such as duvets or
sleeping bags.
9
Maintenance and Cleaning
You must disconnect the appliance from the
electricity supply, before you can carry out any
cleaning or maintenance work.
After a while, a withish patina due to detergent
residue on laundry forms on the filters. When this
occurs, clean the filters with warm water using a
brush. Remove the filter in the door opening as per
picture (it can be positioned with the tooth facing to
the left or to the right).
External cleaning
Use only soap and water and then dry thoroughly.
R
S
E
650
E
R
-
-
6
3
0'
5'
T
O
50'
30
'
U
k
g
2
,
5
A
/
120
0
1000
7
/
-
-
90
0
95
'
65'
k
g
1
800
5'
-
-
1
00'
70
'
0
/
120
'
1000
6
80
5'
90
0
85
'
5
0'
/
800
70'
35'
5'
-
5
'
-
-
90
0'
45'
-
3
0'
kg
5
kg 2,5
5
Important: do not use methylated spirit, diluents or
similar products.
Cleaning the door
Clean periodically the interior part of the door to
remove any fluff from the seals around the filter.
P1152
Accurate cleaning ensures correct drying.
S
E
650
E
R
E
V
-
-
60'
T
O
R
,5 50'
30
'
A
U
/
120
0
kg
k
g
2
1
3
5'
1000
0
/
-
-
90
95
'
65'
800
-
-
7
5'
/
120
0
'
1
00'
70
'
1000
80
5'
0
5
0'
/
90
800
70'
35'
-
85
'
6
5'
5
90
0'
'
-
-
-
45'
5
2
3
0'
kg
kg
5
,5
Do not use the appliance without filters.
Cleaning the condenser
unit
Clean the condenser when light
cleaning) comes on.
(Condenser
P1150
The condenser is situated at the lower part of the
cabinet behind a small door. To open the door, push
the catch as per picture.
Cleaning the filters
Your dryer will only function well if the filters are
clean.
The filters collect all the fluff which accumulates
during drying and they must therefore be cleaned at
the end of each programme, before removing the
laundry, with a damp cloth.
P1153
The light
(Filter cleaning) is on to remind you to
carry out this operation.
During the drying cycle or at the end, it is normal for
water to be present on the surface of the condenser
insertion.
E
650
E
R
S
V
60'
O
R
E
-
-
T
50'
30
'
U
A
/
120
0
kg 2,5
kg
3
5'
1000
7
/
-
-
90
0
95
'
65'
1
800
5'
-
-
120
0
1
00'
70
'
/
'
1000
6
80
5'
90
0
85
'
5
0'
/
800
70'
35'
5'
-
5
90
0'
'
-
-
45'
-
3
0'
kg
5
5
k
g
2
,
5
To pull out the condenser, first turn the two red stops
downwards and then remove the condenser unit
holding it at the handle.
P1151
P1110
The filter in the inner door must be removed for
cleaning.
Do not be alarmed by the amount of fluff. It is not
due to excessive wear caused by the dryer. All fabric
loses fluff when drying but it goes un-noticed in the
air. In a tumble dryer it simply collects in the filter.
P1154
P1155
10
Clean it with a brush and rinse it under the shower if
necessary.
“START/PAUSE” button has to be depressed
again to allow the programme to continue.
Handy tip: The condensed water may be used in a
steam iron or to top up a battery, etc. In this case it
must be filtered (e.g. through a coffee filter).
Cleaning the air intake
grille
Using a vacuum cleaner remove the fluff from the air
intake grille at the back of the appliance.
P0639
Also clean the outside, removing all fluff.
Clean the rubber seal round the condenser cabinet
and in the inner part of the small door with a damp
cloth.
Important! Do not use pointed objects or utensils to
clean the spaces between the plates, as this could
damage the condenser and make it permeable.
Re-fit the condenser, turn the red stops upwards and
close the door.
P1162
Do not use this appliance if the condenser
has not been fitted.
Cleaning the drum
When your laundry does not reach the desired degree
of dryness, in other words, when it turns out either
too dry or too damp, we advise you to clean the
inside of the drum with a cloth soaked with vinegar.
Emptying the water
reservoir
This will eliminate the slight patina that has formed
in the drum (due to residues of detergent and
softeners used in the washing, and to the lime
contained in the water), which prevents the probes
from detecting the correct degree of dryness.
Water extracted from the laundry condenses inside
the machine and is collected in a reservoir.
The reservoir must be emptied after each drying
cycle to ensure efficient operation when the machine
is next used. The pilot light
reminds you this operation.
(Water reservoir full)
Proceed as follows:
• Pull out the reservoir
• Turn it upside down and let water flow down
• Re-fit the reservoir
P1157
P1156
The reservoir must be re-inserted correctly.
If this is not done the pilot light
comes on during
next drying and the programme stops, leaving the
laundry damp. The buzzer will sound.
After emptying and inserting the reservoir the
11
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Possible causes
Symptom
• The door(s) has (have) not been closed.
• The plug is not properly inserted in the power socket.
• There is no current at the socket.
The tumble dryer does not start
• The main fuse or the fuse in the plug has blown.
• The selector dial is not set correctly.
• The water reservoir is full or not properly inserted
(the pilot light
is on ).
• The Start Button
has not been depressed.
• The laundry has not been spun properly.
• The filters and/or the condenser are clogged up.
• The water reservoir is full.
Drying takes too long or laundry is not
dry enough.
• The room temperature is too high.
• The selected time or drying cycle was not suitable
for the laundry.
• The low temperature button
has been pressed.
• There is too much laundry
inside the appliance.
If after the above checks, there is still a fault, call your local Service Force Centre.
Before calling out an engineer, please ensure you
have read the details under the heading “Something
Not Working”.
Service & Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance
(found on the rating plate)
0870 5 929929
Your telephone call will be automatically routed to
the Service Force Centre covering your post code
area.
For the address of your local Service Force Centre
and further information about Service Force, please
For Customer Service in Ireland please contact us at
the address below:
5. The purchase date.
Please note that a valid purchase receipt or
guarantee documentation is required for in-
guarantee service calls.
Zanussi Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: +353 (0)1 4090751
Email: [email protected]
12
Customer Care Department
Major Appliances
Addington Way
Luton
Customer Care Department
For general enquiries concerning your Zanussi
Electrolux appliance or for further information on
Zanussi Electrolux products, please contact our
Customer Care Department by letter or telephone at
the address below or visit our website at
Bedfordshire
LU4 9QQ
Tel 08705 727727*
To buy accessories, consumables and spare parts at
electrolux.co.uk
* calls to this number may be recorded for training
purposes.
Guarantee Conditions
●
Appliances found to be in use within a
commercial environment, plus those which are
subject to rental agreements.
Standard guarantee conditions
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is
proved to be defective by reason only of faulty
workmanship or materials, we will, at our option
repair or replace the same FREE OF ANY CHARGE
for labour, materials or carriage on condition that:
●
Products of Zanussi Electrolux manufacture
which are NOT marketed by Zanussi Electrolux.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
●
The appliance has been correctly installed and
used only on the electricity supply stated on the
rating plate.
The guarantee starts from the date you first
purchased your product.
●
●
The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.
The guarantee is for the same period and to the
●
same extent for labour and parts as exists in the
new country of use for this brand or range of
products.
●
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
The guarantee relates to you and cannot be
transferred to another user.
●
●
All service work under this guarantee must be
undertaken by a Service Force Centre.
Your new home is within the European
Community (EC) or European Free Trade Area.
●
●
Any appliance or defective part replaced shall
become the Company’s property.
The product is installed and used in accordance
with our instructions and is only used
domestically, i.e. a normal household.
●
●
This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be
charged.
The product is installed taking into account
regulations in your new country.
●
Before you move please contact your nearest
Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your move
and able to look after you and your appliances.
Exclusions
This guarantee does not cover:
France
Germany
Italy
Senlis
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
+39 0434 39 4700
●
Damage or calls resulting from transportation,
Nurnberg
Pordenone
Stockholm
Luton
improper use or neglect, the replacement of any
light bulbs or removable parts of glass or plastic.
Sweden
UK
+46 (0) 8 672 53 90
●
Costs incurred for calls to put right an appliance
+44 (0)
which is improperly installed or calls to
appliances outside the United Kingdom.
8705 727727
Ireland
Dublin
+353 (0)1 4090751
13
Adjusting the level of conductivity
Water contains, a variable quantity of limestone and
mineral salts of which quantities vary according to
geographical locations thus varying its conductivity
values.
Adjusting the level of conductivity:
Press the START/PAUSE
button sequentially:
the level of conductivity is indicated by the phase
pilot lights, which light in various combinations as
follows:
Relevant variations of the conductivity of the water
compared to those prefixed by the factory could
slightly influence the residual humidity of the
laundry at the end of the cycle.
Approximate value
LED lit
Conductivity
Low
µS/cm
Your dryer allows you to regulate the sensitivity of
the drying sensor based on conductivity values of the
water by using the following procedure.
< 300
Medium
High
300 - 600
> 600
To access adjustment mode:
Turn the programme selector dial to switch on the
appliance. In selection mode, press simultaneously
the buttons 1 and 3.
Press the buttons down until the pilot lights above
each ones begin to flash and one of the pilot lights
Normally, the appliance is factory-set to the highest
level; however, certain models may be configured
differently.
indicating the drying phase lights , cooling
end cycle remains lit.
,
or
Memorizing the new setting:
Simultaneously press the buttons 1 and 3.
Press the buttons down until the pilot lights above
each ones stop flashing and the buzzer sounds.
1
3
4
2
14
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm (33.5”)
60 cm (23.6”)
58 cm (22.8”)
POWER SUPPLY VOLTAGE
TOTAL POWER ADSORBED
240 V/50 Hz
2450 W (13A)
MAX LOAD CAPACITY
Cotton, linen
Synthetics
6.kg (13.2 lbs)
3 kg (06.6 lbs)
DRUM VOLUME
CONSUMPTIONS
108 l
Cotton, linen
Cotton, linen
Synthetics
3.36 kWh (6, kg store dry)
2.70 kWh (6, kg iron dry)
1.20 kWh (3 kg store dry)
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
Positioning
Unpacking
It is recommended that, for your convenience, the
machine is positioned close to your washing
machine.
Warning !
Slide out the polythene bag containing the
polystyrene block before using the appliance.
Pull off adhesive strips from inside machine on
top of drum
The tumble dryer must be installed in a clean place,
where dirt does not build up.
Air must be able to circulate freely all round the
appliance. Do not obstruct the front ventilation grille
or the air intake grilles at the back of the machine.
To keep vibration and noise to a minimum when the
dryer is in use, it should be placed on a firm, level
surface.
Once in its permanent operating position, check that
the dryer is absolutely level with the aid of a spirit
level. If it is not, raise or lower the feet until it is.
The feet must never be removed.
Do not restrict the floor clearance through deep-
pile carpets, strips of wood or similar. This might
cause heat build-up which would interfere with
the operation of the appliance.
P1106
Should the appliance be moved, it must be
transported vertically.
15
Important
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the
appliance’s rating plate. (See picture on page 4).
The hot air emitted by the tumble dryer can reach
temperatures of up to 60°C. The appliance must
therefore not be installed on floors which are not
resistant to high temperatures.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved BS 1363/A fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below. The wires in the mains lead
are coloured in accordance with the following code:
When operating the tumble dryer, the room temperature
must not be lower than +5°C and higher than +35°C, as
it may affect the performance of the appliance.
Stacking kit (optional accessory)
It should be possible to stack your new dryer on top
of a front loading washing machine with a worktop
depth between 48 and 60 cm.
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
Read carefully the instructions supplied with the kit.
GREEN & YELLOW
Please contact your local Service Force Centre for
further advice.
E
L
N
BROWN
BLUE
CORD CLAMP
P1041
The wire coloured green and yellow must be
connected to the terminal marked with the letter «E»
P1148
or by the earth symbol
yellow.
or coloured green and
The wire coloured blue must be connected to the
terminal «N» or coloured black.
Door reversal
To make it easier to load or unload the laundry the
door can be reversed.
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
This operation must be carried out by qualified
personnel.
Please contact the nearest Zanussi Service Force
Centre.
This will be a chargeable option.
WARNING:
A cut off plug inserted into a 13 amp socket
is a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
Permanent connection
In the case of permanent connection it is necessary
that you install a double pole switch between the
appliance and the electricity supply (mains), with a
minimum gap of 3mm between the switch contacts
and of a type suitable for the required load in
compliance with the current electrical regulations.
The manufacturer declines any liability
should this safety measure not be observed.
Should the appliance power supply cable
need to be replaced, this must be carried out
by our Service Centre.
The switch must not break the yellow and green
earth cable at any point.
The power supply cable must be accessible
after installing the machine.
16
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.
© Electrolux plc 2006
|