REFRIGERATOR
CZL 145 W
INSTRUCTION BOOKLET
2222 027-92
CONTENTS
Instructions for the User
Instructions for the
Installer
2
4
5
Important Safety Information
Description of the Appliance
13
14
Technical Specification
Installation
Positioning
Operation
14
14
Before use
5
5
5
5
6
6
7
Rear Spacers
Setting the temperature
Fresh food refrigeration
Normal operating sounds
Movable shelves
15
16
Electrical Connection
Door Reversal
Positioning the door shelves
Cool Check Guide
8
8
Hints and Tips
Maintenance and Cleaning
Internal cleaning
8
8
8
9
9
External cleaning
When the appliance is not in use
Changing the light bulb
Defrosting
10
11
11
12
Something Not Working
Service and Spare Parts
Customer Care
Guarantee Conditions
2222 027-92
3
DESCRIPTION OF THE APPLIANCE
I
A
B
C
H
D
G
F
E
A- Dairy compartment
B- Movable shelf
C- Can storage shelves
D- Bottle storage shelf
E- Salad crisper
F- Glass shelf
G- Cool Check Temperature Guide
H- Storage shelves
I- Interior light
4
OPERATION
Before using
Fresh food refrigeration
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Setting the temperature
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and an
«OFF» (O) position.
Raw meat (beef, pork, lamb & wild fowl): wrap in
polythene bags and place on top of the salad
crispers.
Position 1 = minimum coldness
Meat can only be stored safely in this way for
one or two days at the most.
Position 6 = maximum coldness
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad crispers.
Turn the thermostat dial to the required position.
The intermediate position is usually the most
suitable (3-4).
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
– room temperature
– how often the door is opened
– how much food is stored
– position of the appliance
Normal Operating Sounds
Important
•
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
During prolonged periods of abnormally hot weather,
if the thermostat is set on too high a number, the
cooling system may operate continuously and the
fridge cooling plate may not defrost. Turning the
knob to a lower number will cause the automatic
defrosting to resume.
plate/evaporator or to the fixed freezer shelves.
•
•
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
A thermostat controls the compressor, and you
will hear a faint ’click’ when the thermostat cuts in
and out.
5
Movable shelves
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
D040
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To do this proceed as shown in the diagram.
PR261
6
Cool Check Guide
The guide consists of a temperature sensitive strip
sealed in a shelf trim.
When the fridge is operating at the safe temperature
to store food the guide will appear black. If the
temperature rises above this level the guide will
show the words TOO WARM.
TOO WARM
Positioning of the Cool Check
The shelf with the cool check temperature guide
must be placed in the fridge according to the
instructions located on the fridge wall and always
ensure the guide is at the front.
If the Cool Check shows TOO WARM
In certain conditions the temperature guide may
show TOO WARM if:
•
•
•
The fridge is switched off
ZANUSSI
The door has been recently opened
A quantity of warmer food has been introduced to
the fridge
CCOO2
•
The fridge temperature is above the
recommended maximum for the safe storage of
food.
The cool check will change to show “TOO WARM“
very quickly after the door has been opened. It will
however take a number of hours to return to black,
indicating that the temperature is correct.
The appliance should be left overnight and the cool
check examined in the morning. If the cool check
shows TOO WARM, turn the thermostat to a colder
setting leave overnight and examine again the
following morning.
Hints and Tips
•
•
•
The guide is only suitable for use in the model
supplied.
The guide will not operate in a freezer
compartment.
When cleaning the shelf take care not to immerse
in water, and wipe away any spills.
7
HINTS AND TIPS
Food Storage
Energy Saving Advice
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
•
To obtain the best results from the appliance
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
•
•
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
•
•
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
•
•
Always leave warm food to cool down to room
temperature before placing in the fridge.
Do not push food together too much, try to allow
air to circulate around each item.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
•
•
Do not store food uncovered.
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
•
•
Ensure there are no obstructions preventing the
door from closing properly.
It is advisable to peridocally clean the
refrigeration system at the back of the appliance
with a duster or vacuum cleaner.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
You MUST ensure that the appliance is switched
OFF.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED CLEANING
PRODUCTS OR WAX POLISHES, TO CLEAN THE
INTERIOR AS THESE WILL DAMAGE THE
SURFACE AND LEAVE A STRONG ODOUR.
PR259
External cleaning
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
8
Changing the light bulb
Unscrew the light cover and then pull it outward
toward the middle of the cabinet. Unscrew the bulb
and replace it with a new 15 watt bulb (available
from your nearest Service Force Centre).
Replace the light cover by sliding it into its original
position and replacing the screw.
D411
Defrosting
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
D037
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry throughly before
replacing.
9
SOMETHING NOT WORKING
If the appliance is not working correctly, please carry out the following checks before contacting your local
Zanussi Service Force Centre
Symptom
Solution
No power to the appliance
Check there is power at the socket.
Check there is not a power cut by checking the
household lights.
Check the fuse has not blown.
The light does not come on
The temperature in the fridge
Ensure that the bulb is correctly fitted.
Replace the bulb if it has blown.
Check the door light switch is not jammed.
Check the thermostat control knob in the fridge is
turned to the correct setting relative to ambient
conditions.
Check the ambient temperature is within the
appliance’s operating limits, please refer to the
installation section in this instruction book.
Relocate the appliance if necessary.
The compressor runs continously
Adjust the thermostat control knob to give correct
temperature control. See “Setting the temperature”.
Check that the door is closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Check that air ventilation is not obstructed.
Refer to normal operating sounds.
Noise
Water under the salad crispers
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
If after the above checks your appliance still does not operate correctly, contact your local Zanussi Service
Force Centre.
Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have been made, as the engineer will
make a charge if the fault is not a mechanical or electrical breakdown.
10
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Zanussi Service Force Centre by telephoning:-
0870 5 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit the
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
2.
3.
4.
5.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products,
please contact our Customer Care Department by letter or telephone at the address below or visit our website
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727 727 (*)
* calls to this number may be recorded for training purposes.
11
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 29
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)1753 219 897
Nürnberg
Pordenone
Stockholm
Slough
Sweden
UK
12
TECHNICAL SPECIFICATIONS
DIMENSIONS
Height
140
55
60
cm
Width
Depth
cm
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
TOTAL POWER ABSORBED
AVERAGE DAILY UNITS ELECTRICITY *
GROSS CAPACITY
220-240 V / 50 Hz
90 W
0.62 kWh
263 l
NET CAPACITY
260 l
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
13
INSTALLATION
Important
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE THAT
HAS A LOCK OR CATCH ON THE DOOR, YOU MUST
ENSURE THAT IT IS MADE UNUSABLE TO PREVENT
YOUNG CHILDREN BEING TRAPPED INSIDE.
Depending upon the position which you choose for your
appliance, you may wish to reverse the way in which
the door opens. To do this, refer to instructions on “Door
reversal”.
It must be possible to disconnect the appliance from
the mains power supply; the plug must therefore be
easily accessible after installation.
Please ensure that when the appliance is installed it
is easily accessible for the engineer in the event of
a breakdown.
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate, which
is located at the left on the inside of the appliance.
The following table shows which ambient temperature is
correct for each climate classification:
SN +10°C to + 32°C
N
+16°C to + 32°C
ST +18°C to + 38°C
+18°C to + 43°C
A
B
T
It should be located in a dry atmosphere, out of direct
sunlight and away from extreme temperature e.g. not
next to a boiler or radiator, or in a very cold room e.g. an
outhouse, where the temperatures may fall below 10°C
(50°F). If these temperatures are exceeded i.e. colder or
warmer, then the appliance may not operate correctly.
NP007
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There must
also be at least 100 mm (4”) distance between the top of
the cabinet and any overhanging kitchen furniture (A).
Ideally, the appliance should not be positioned beneath
overhanging furniture (B).
There should also be a gap of 25 mm either side of the
appliance. Do not obstruct the space underneath. The
back of the cabinet may be placed close to the wall but
must not touch it. DO NOT install in places with
restricted ventilation.
D200
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.
Rear spacers
The plastic bag containing all relevant
documentation also contains two spacers to be fitted
into special holes in the back of the appliance.
A
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in the
diagram. Then turn them through 45° (arrow (A)
vertical) until they lock into place.
45°
PR60
14
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
Electrical connections
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
A replacement cover/carrier must be obtained from
your local Zanussi Service Force Centre.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not
correspond with the markings identifying the
terminals in your plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
BROWN
BLUE
CORD CLAMP
D207
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
15
Door reversal directions
1. Disconnect from the electricity supply.
2. Remove all loose items, including food, store food
in a cool place.
3
3. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
1
4. Remove the feet (3)
5. Remove bottom hinge (1).
D715 PIED/C
6. Slide out the door from pin (G), unscrew the
latter and then screw it down into the hinge
provided on the opposite side, after having
removed the small plugs which should then be
fitted on the opposite side.
7. Refit the door and bottom hinge (1) on the
opposite side.
G
8. Refit the feet (3) on the opposite side.
9. Unscrew the handle. Refit it on the opposite side
after having pierced the plugs with a punch.
Cover the holes left open with the plugs contained
in the documentation pack.
Attention
After completion of the door reversiing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdrier.
D162/1
Printed on recycled paper
16
© Electrolux plc 2002
|